Water pump change in Morphy Richards steam iron

Your steam generator iron just stopped to work, there is no steam from it. Warranty on the appliance is finished! Was very expensive!

Manufacturer asking £80 for repair!

If you visit my website it means that your Morphy Richards steam generator is no working properly.

You can fix steam generator iron of other makers, they are similar to repair.

I am a qualified electrician, have fixed 100's of these irons and sold 100's of pumps.

First of all, make sure your iron is unplugged and cool.

At the bottom you will need to unscrew 5 screws, then split into halves.

The top half is attached to the bottom by wires at the switch end.

Morphy Richards non-pressurised steam generator iron opened.

The water pump is placed between the boiler and water tank, a green item with 3 wires.

To disconnect wires you will need a screwdriver or something similar as there is protection on the connectors, won't come off easily. Need to push a middle of the connector to release it and then pull it.

Water pump replacement in Morphy Richards steam generator iron

Lift up white cable tie.

Faulty water pump removal from the iron.

Move white rubber ring out of the black end of the pump.

Water pump removal from steam generator iron.

Move white rubber ring out of the black plastic part of the pump.

Faulty water pump in steam generator iron removed.

Disconnect hose from white tower connected to the water tank.

Pull this hose through the white ring.

Put back on cable tie on the neutral connector of the pump.

Hold white plastic ring and pull off the pump, place new pump into that hose, but make sure you pushed to the end.

Water pump put back in Morphy Richards steam generator iron.

Place inlet hose back through white rubber ring and connect to white tower connected to the water tank.

Connect wires to the pump, make sure wires are away from holes where screw comes through.

Morphy Richards steam generator iron repaired.

The best way to put back cable tie on the white tower, pictured above.

Put back the whole base and test it.


Created On Wednesday, August 22, 2018 Posted By Mayur Patel Comment Link
IS there a replacement pump available for the Model 330001 as my irons pump is no longer firing up. Everything else seems fine.
Created On Tuesday, August 7, 2018 Posted By margaret fleming Comment Link
I have a morphy richards steam generated iron which has just flooded everywhere. I have opened it up and the yellow plastic fitting that the hose fits onto has a small hole in it . Can I purchase a replacement one
Created On Monday, August 6, 2018 Posted By Tina Comment Link
I also have a Morphy Richards steam iron that has stopped generating steam. Tried to unscrew the water tank into 2 halves but cannot achieve this. It’s my second Morphy Richards Iron, this one less tha 3 years old and quite frankly the iron is not fit for use. We a couple and this iron has been rarely used less than 2 hours per week. DONT BUY ONE my model 42244.
Created On Wednesday, June 13, 2018 Posted By Judith Wickson Comment Link
I have receuved my replacement pump this morning, superfast delivery thank you, but I cannot get the iron to split into two halves. It is a Power Steam Elite 330003, could you please advise. Many thanks.
Created On Wednesday, June 13, 2018 Posted By Judith Comment Link
I have received the replacement pump this morning but cannot get the iron to split into two halves. My model is a power steam elite 330003. Could you please advise? Many thanks
Created On Monday, June 11, 2018 Posted By Susan Comment Link
I have a Morphy Richards Power Steamelite 332001 that was intermittently steaming when switched on and the pump made noise. Now the pump seems dead and no steam, would this pump fit my model. Thanks Susan
Created On Saturday, June 2, 2018 Posted By Michael Flay Comment Link
How much is a pump for morphs Richards steam generator
Created On Wednesday, May 9, 2018 Posted By Anthony Prince Comment Link
Hi, how much are the pumps and where can i buy one? Regards 4
Created On Sunday, March 25, 2018 Posted By Megan Rowe Comment Link
Hello, I have a MR steam elite steam generator iron and didn’t descale it sufficiently. There was then a whistling noise and a hush of steam and the water from the tank started leaking out of a hole in the bottom of the base. Can this be fixed, and if so, is it something I can buy parts for and do myself? Thanks in advance for your help.
Created On Friday, February 9, 2018 Posted By bovario Comment Link
To Julie Williams In these models, there is a valve to release steam. The valve looks like not opens every time, the reason may be a limescale or loosen the electrical connection. Micro-switch in the handle can be blamed as well as connectors can be burned. I would start from the switch in the handle checking. Regards admin
Showing 1 - 10 of 23 items

Leave your comment